Above values from ASTM A Higher strengths can be produced by heavy cold work – this may be required for certain applications. ASTM A – 16 Standard Specification for Stainless Steel Wire and Wire Rods for Cold Heading and Cold Forging. This specification covers. See the chemical composition and physical properties of ASTM A Grade annealed Stainless Steel, find alternative materials, and connect with suppliers.

Author: Yozshuzragore Voodoom
Country: Honduras
Language: English (Spanish)
Genre: Marketing
Published (Last): 5 September 2016
Pages: 281
PDF File Size: 13.26 Mb
ePub File Size: 12.3 Mb
ISBN: 440-2-73101-765-2
Downloads: 45014
Price: Free* [*Free Regsitration Required]
Uploader: Faejora

It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application.

This specification covers cold-finished and hot-finished stainless steel wire and wire rods for cold heading or cold forging for applications, such as fasteners, where corrosion resistance is a factor.

Copyright ASTM Standard Specication for Stainless Steel Wire and Wire Rods for Cold Heading and Cold Forging1 This standard is issued under the xed designation A ; the number immediately following the designation indicates the year of original adoption or, in the case asrm revision, the year of last revision.

The American Society for Testing and Materials takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard.

This standard has been approved for use by agencies of the Department of Defense.

The material shall also conform to the requirements as to mechanical properties. A number in parentheses indicates the year of last reapproval. For smaller sizes, similar mechanical properties apply to ferritic and martensitic grades; however the producer should zstm consulted regarding somewhat higher tensile properties applicable to austenitic grades. The following coatings may be specied: The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

Related Posts (10)  BA4558 PDF

B Product analysis tolerance over the maximum limit for carbon and nitrogen to be 0.

ASTM A for Stainless Steel Wire and Wire Rods for Cold Heading and Cold Forging

ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date. Such requirements may include, but are not limited to the asym All austenitic grades in the annealed condition or annealed and lightly drafted condition shall be capable of passing the criteria set by this specification.

Current edition approved Jan. Resistance to Intergranular Corrosion 8. Link to Active This link will always route to the current Active version of the standard. Last previous edition A — The steel shall conform to the required chemical composition requirements. An electroplated copper coating is often used.

ASTM A493 Grade 384 annealed

Originally published as A — Soap is generally used. General Requirements for Delivery 4.

ICS Number Code Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. The SI equivalents are in parentheses and may be approximate.

Related Posts (10)  ASTM D1004 PDF

Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. This standard is subject to revision at any time by the responsible technical committee and must be reviewed every ve years and if not revised, either reapproved or withdrawn. Historical Version s – view previous a943 of standard.

ASTM A493 for Stainless Steel Wire and Wire Rods for Cold Heading and Cold Forging

This abstract is a brief summary of the referenced standard. NOTE 1—A typical ordering description is as follows: A superscript epsilon e indicates an editorial change since the last revision or reapproval. The following lubricants may be specied: Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM Headquarters. Ast can be manufactured to tensile strength ranges other than those shown in Table 2.

Users of this atm are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility. The producer should be satm when material is required to tensile strength ranges other than those specied.

Packaging and Package Marking 9.